West Coast
AREDN

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== IP Direct Calling  ======
<WRAP center round tip 80%>
The following instructions((First of draft of this page was copied with permission from [[https://groups.io/g/Mid-Island-AREDN-Mesh-Network/topic/direct_ip_dialing_manual/88087211 | Mark N2MH, Rich VE7BEF, Devan VE7LSE's document (v1.5)]])) are to make direct IP-to-IP calls using the Cisco SPA525G or SPA504G phones.  For instructions on using our local PBX, see the [[/services/voip/ |instructions are here]].
</WRAP>


===== General Notes: =====

  * All steps are done as Administrator on the advanced page.
  * This setup will configure the last extension and line key for direct IP dial calls and leave extension 1 / line key 1 for PBX calls.
  * It may be a good idea to ''Submit All Changes'' after each step but it also may be unnecessary.
  * Outgoing calls may be placed from the personal directory, speed dial buttons or the dial pad. When using the dial pad, end the IP address with a <key>#</key> character. This will send the call out immediately.
  * If you like, you can publish your phone’s IP number on the mesh status page so others can add your phone directly.
  * If you are replacing an existing speed dial button with the new direct dialing Line, make sure to remove the previous info in the ''Short Name'' and ''Extended Functions'' boxes.


<pagebreak>

===== SPA525G =====
==== Ext 1 tab ====
  * SIP Settings
    * SIP Port: ''5070''
{{  directip01.png  }}

<pagebreak>
==== Ext 5 tab (or any free Ext you want to use) ====
  * General
    * Line Enable: ''yes''
  * SIP Settings
    * SIP Port: ''5060''
{{  directip02.png  }}

<pagebreak>
  * Proxy and Registration
    * Register: ''no''
    * Make Call Without Reg: ''yes''
    * Ans Call Without Reg: ''yes''
  * Subscriber Information:
    * Enter your Call and Direct for example
{{  directip03.png  }}

  * Dial Plan
    * Dial Plan: ''(x.<*:.>x.<*:.>x.<*:.>x.)''
    * Enable IP Dialing: ''Yes''
{{  directip04.png  }}

<pagebreak>
==== Phone tab ====
  * Line Key 1
    * Extension: ''1''
  * Line Key 5
    * Extension: ''5'' or your preference Line Key

<WRAP center round important 60%>
Make sure your line keys do not have anything entered for extended Function.
</WRAP>

{{  directip05.png  }}


<pagebreak>
==== Outgoing Direct-IP dialed calls ====

=== Personal Directory ===
This section is done on the phone itself.  To add to the directory:
  * Press your line key that is setup for direct dialing
  * Dial IP of the phone you want to call (using the <key>*</key> key as a ''.'') \\ For example, to enter ''10.10.123.123'', key in: <key>1</key><key>0</key><key>*</key><key>1</key><key>0</key><key>*</key><key>1</key><key>2</key><key>3</key><key>*</key><key>1</key><key>2</key><key>3</key>
  * Press <key>Dial</key> to make sure it works.
  * Press Setup button: {{cisco_spa525g_setupkey.jpg?25}}
  * Navigate to ''2. Call History''
  * Navigate to ''4. Placed Calls''
  * Navigate to the call you just placed using the IP Address
  * Press the <key>%%Option%%</key> button.
  * Navigate to ''Add to Address Book''
  * Enter the info you want in there then press <key>save</key>

The reason for this method is that the SPA525G does not recognize an IP addressed entered into the
web interface when adding a directory entry. If anyone figures out a work around, please let us know.


<pagebreak>
How to add direct IP contacts to your speed dial buttons on your phone’s spare line keys or Attendant
Console keys:

=== Phone ===
  * Line Key //x//
    * Extension: ''Disabled''
    * Short Name: Enter a short name
    * Extended Function: Enter something like: ''vid=5;fnc=sd;ext=10.46.174.182''

<WRAP center round info 60%>
  * ''vid=5'' refers to the line key used for this speed dial button
  * Change the IP address and name to the correct one you are trying to add
</WRAP>

{{  directip07.png? }}

=== ATT Console ===
  * Cut and paste this example into a free “Unit 1 or Unit 2 Key”:<code>
vid=5;fnc=sd;ext=10.46.174.182;nme=VA7PF DIRECT</code>
{{  directip06.png?800  }}

<pagebreak>
===== SPA504G =====

==== Ext 1 tab ====
  * SIP Settings
    * SIP Port: ''5070''
{{  directip08.png  }}

<pagebreak>
==== Ext 4 tab or any free Ext you want to use ====
  * General
    * Line Enable: ''yes''
  * SIP Settings
    * SIP Port: ''5060''
{{  directip09.png  }}

  * Proxy and Registration
    * Register: ''no''
    * Make Call Without Reg: ''yes''
    * Ans Call Without Reg: ''yes''
  * Subscriber Information
    * Enter your Call and Direct for example
{{  directip10.png  }}

  * Dial Plan
    * Dial Plan: ''(x.<*:.>x.<*:.>x.<*:.>x.)''
  * Enable IP Dialing: ''Yes''
{{  directip11.png  }}


==== Phone tab ====
  * Line Key 1
    * Extension: ''1''
  * Line Key 4
    * Extension: ''4'' or your preference Line Key

<WRAP center round important 60%>
Make sure your line keys do not have anything entered for extended Function.
</WRAP>

{{  directip12.png  }}

==== Outgoing Direct-IP dialed calls ====

=== Personal Directory ===

In each box, place an entry for each desired phone. Examples:<code>
n=VE7LSE;p=10.1.2.3
n=N2MH;p=10.73.73.66
</code>
{{  directip13.png  }}

<pagebreak>
How to add direct IP contacts to your speed dial buttons on your phone’s spare line keys or Attendant
Console keys:

=== Phone ===
  * Line Key //x//
    * Extension: ''Disabled''
    * Short Name: Enter a short name
    * Extended Function: Enter something like: ''vid=4;fnc=sd;ext=10.46.174.182''

<WRAP center round info 60%>
  * ''vid=4'' refers to the line key used for this speed dial button
  * Change the IP address and name to the correct one you are trying to add
</WRAP>

{{  directip14.png? }}


=== ATT Console ===
  * Cut and paste this example into a free “Unit 1 or Unit 2 Key”:<code>
vid=5;fnc=sd;ext=10.46.174.182;nme=VA7PF DIRECT</code>
{{  directip06.png?800  }}